Part Application Footnotes
| Footnote ID | Description |
| (2) | Two batteries may be required |
| (3) | Three batteries may be required |
| (4) | Four batteries may be required |
| (5) | Five batteries may be required |
| 6 | Best-fit estimate, may need to be modified. Check clearance before connecting cables |
| 7 | Check polarity before connecting cables |
| 8 | In the absense of a cold cranking rating, the amphour rating is shown |
| 9 | Manufacturer's recommended replacement battery shown, may vary from OE battery |
| 10 | Modification of the holddown may be necessary |
| 11 | OE battery has flush vents |
| 12 | OE battery has type F terminals |
| 13 | On vehicles equipped with an electrolyte sensor, adapter kit required |
| 14 | Polarity reversed, check before installing |
| 15 | Polarity varies in production, some vehicles require a Group 26R, check before installing |
| 16 | Requires individual vent caps for proper hood clearance, do not fit batteries with pod type vent caps |
| 17 | Requires special height battery of 7 1/4" (184 mm) maximum |
| 18 | *** RESERVED *** |
| 19 | See manufacturer's service information for retrofit |
| 20 | Some models require Group 91, check OE battery |
| 21 | Some vehicles may use a Group 35, check polarity before installing |
| 22 | Special 12-volt: 9 5/8" X 6 7/8" X 7 9/16", check polarity before installing |
| 23 | Special 12-volt: 10" X 6 1/16" X 8 3/8", Assembly no. 25. Check polarity before installing |
| 24 | Special 12-volt: 14 15/16" X 6 3/4" X 7 3/8" |
| 25 | Special 12-volt: 8 1/4" X 6 3/4" X 7 1/4", Assembly no. 15 |
| 26 | Special 12-volt: 9 3/4" X 5" X 7 1/2", battery is vented to outside of vehicle |
| 27 | Special 12-volt: 9 7/8" X 6 21/32" X 3 11/16", Assembly no. 11 |
| 28 | Special 12-volt: 9 9/16" X 6 13/16" X 6 11/16", Assembly no. 26 |
| 29 | Special 12-volt: 9 9/16" X 6 13/16" X 6 13/16", Assembly no. 24. Check polarity before installing |
| 30 | Special 12-volt: 9" X 7 1/4" X 7 1/2", Assembly no. 15 |
| 31 | Requires special deep cycle battery |
| 32 | Special maintenance-free cycling battery |
| 33 | *** RESERVED *** |
| 34 | Vibration resistant battery |
| 35 | Without handle bracket |
| 36 | Identical to 72H shown in manufacturer's literature |
| 37 | Check hood clearance |
| 38 | *** RESERVED *** |
| 39 | Remote vented |
| 40 | Battery is encased within an "Active Cooling Box" with an air snorkle to the outside of the engine compartment |
| 41 | Uses motorcycle battery, no BCI equivalent |
| 42 | Same dimensions as Group 27 but uses type X terminals |
| 43 | O.E. battery has non-standard terminal location. May require cable modifications |
| 44 | w/o HBL but with ETR, Travel Computer Cluster or Audible Message Center |
| 45 | Non-BCI Group Size |
| 46 | Dual terminal battery |
| 47 | OE Battery Valve Regulated Lead Battery |
| 48 | Trailer Tow Package, Engine Heater or Canada |
| 49 | Requires Special Steel Tray |
| 50 | Uses starting or deep cycle type battery |
| 51 | Gel Electrolite |
| 52 | DIN Size |
| 53 | A battery spacer kit is required on some models |
| 54 | Battery is vented to outside of vehicle |
| 55 | Battery may require vent hose |
| 56 | Amp-hour rating from O.E. manufacturer is converted to approximate CCA rating (Ah x 10 = approximate CCA) |
| 57 | O.E. manufacturer used various size batteries in production. Carefully size to fit. |
| 58 | Check polarity before installing, may vary in rpoduction |